(c) MONTESA 4RT *new* 6mm H30 Dural Alluminum extra strong sumguards. These super tough guards are exclusive to us , as we have designed these to our own spec in conjunction with  expert riders and they are one of our best selling 'home' products. They are longer than standard to give added protection to the rear linkage whilst also being slightly wider to give added protection to the engine cases and especially the vunerable water pump , we have also 'kicked' them out a little where the rear mounting holes are as we have seen other aftermarket guards crack around this area from the bolt holes to the edge of the guard. .They are avaliable in standard alloy,bead blast(shown),or many other polyester powder coat anodise look colours, please state preferance when ordering.

Other 'special' colours are avaliable at for an extra£5. Please state a colour when ordering.

Montesa 4RT & 315 rear suspension links

Again exclusive to us, these super links are designed to raise and improve the performance of the rear suspension of the montesa 4rt. They are machined out of strong H30 alluminium and also increase travel and can improve grip and rear end traction whilst eliminating some of the suspension  'sag'. The increase in travel uprates the soft rear end and aids the ability to 'trick' ride and hop around the rear end by providing an even more progressive shock.  Whilst the coloured versions provide that extra bling. Avaliable in most colours that may suit your needs, just state your colour as you order, from standard mill finish to anodized look , red, gold, blue, titanium black ,repsol orange and satin black.. These are not just a shiny 'add on' they are performance upgrade and obviously come as a pair.

We are proud to be able to offer for sale these fantastic best selling hand machined in England billet aircraft grade alluminium rear brake pedals. Upgrade your Montesa from your standard brittle pedals to one of these. You will never have to keep buying  rear pedals again, these pedals are slightly shorter & sit just nicely behind the clutch casing and so the only exposed part is the spring loaded platform part which harmlessly bends out of the way when hit against an object. They are also especially handy for those who are using 'down & back' rear hangers that can make it hard for some to reach the standard pedal! 

They come ready fitted with a new clevis pin , a new bearing and new seals so you can just bolt the pedal straight on and do not have to strip your old one.

Avaliable in billet silver or matt black.

 !! IN STOCK !!

H&D Trials Racing Products flat fush fitting petrol cap breathers. We have made these to our design and spec to replace the standard clumbersome rubber pipe or the short piece of pipe with another alloy breather on that are vulnerable to getting knocked off. It is such a simple and clever idea and unlike other avaliable versions these have 3 seperate 'breather' holes to prevent pressurisation and so there is no need to cut into your fuel cap. Simply remove your rubber pipe and push this little chap on and its done! No more lost caps.

Avaliable in gold, red, titanium black, blue or plain silver.

Rear suspension linkage repair kit ideal to purchase alonside the linkage tuning plates . Rather than having to source all your parts seperately we have put together this kit which consists of 2 genuine inner bushes at £5.95 each, 4 needle roller bearings and 4 seals. The rear linkage needs regular checking as play can soon develop with dirt and water penetrating the bearings and excessive play can lead to damage of the entire rear suspension set up.

Simlilar to the above but designed for the swing arm bush part of the linkage. 1 inner bush ans 2 bearings and 2 seals.

NGK  spec reccomended performance plug

Derived from our 4RT sumpguards, after repeated requests we have developed  a version of our 4RT Heavy duty guards to fit the cota 315. Made from exactly the same H30 quality 6mm thick material these are also longer than standard and wider to give greater protection to both sides of the engine.

You cannot buy a heavy duty , quality guard for the 315 anywhere else in the world!

Complete brake hose to fit the nissin front master cylinder, avaliable seperately, to fit most models. We have had these made specifically for us to fit these m/cylinders as you cannot buy these off the shelf.

 We have had a small batch made of very very special hollow titanium axles for the front and rear wheels to replace the alluminium ones and a swingarm axle to replace the heavy steel one, also hollow. These are factory rider replicas, not avaliable anywhere else!

The kit comprises of 3 hollow axles, 1 swingarm pivot nut and i rear wheel nut & a specific tool for the front wheel, avaliable in blue or gold & high quality grease. These are availiable seperately at a per unit cost of £149.99

IN STOCK

Titanium rear snail cam adjusters to fit 4RT & 315. They are the same size as standard but obviously much lighter and gram for gram much stronger. Some people buy the oversized alloy ones but they are not advised as they are nearly 2mm thicker diameter and so the rear wheel nut doesnt have sufficient thread on the axle which can damage the axle and lead to shearing off. Also a lot of riders do not realise that there is no need for a larger cam as the adjusting bolt in the swing arm is removed and refitted further back in holes provided to provide the extra adjustment.

Quality twin air oil filters for the Montesa 4RT, dont treat your top quality bike to cheap oil filters! Fit These twin air ones, we have a choice what to use in our bikes and we use these as they are the best!

As used by ourselves now for our 4RT's.....

Moto Air filters filter the air better and let more clean air through. Two different layers foam air, the white coarse outer layer and the blue fine inner layer, work effective. After the white layer pre filters the air, the blue layer removes the fine dust particles.

Moto Air filters:

• Are cleanable and re-usable - saves money on replacement filters
• Offer full-depth filtration - stops and holds more dirt than conventional paper air filters
• Improve airflow characteristics - up to 50% more air flow than pleated-paper
• Helps extend engine life - effectively eliminates wear-causing airborne contaminants

Very good quality forged (not like the cheap cast ones) aftermarket lever to fit the nissin large front master cylinder. Comes supplied with the lever play adjuster.

One of our H&D Exclusive bashplates ready fitted with the super tough and bash resistant Repsol graffic onto the front to look just like the pro's. We offer these ready proffesionally fitted onto mill finish, satin black or repsol orange bashplates

Another addition to our range of vent gas cap breathers is also part of our new 'in from Spain' range of Repsol products which here we have a version of our breather tops in repsol orange.

 A must for ltd edition bikes and also to compliment our new tank range.

We are proud to be finally able to bring you our new & already in demand range of hand made flat tanks for the Montesa 4RT. Simply the best out there, put them all alongside one another and there really is no comparison, these have been made by the hands that fabricate many World Superbike tanks and the quality really is that good. No horrible welding where the thread tops have simply been cut out and badly rewelded into place, nor dodgy blobby stuff round the outsides! The tops have been specially pressed, recessed and fused together to enable a much better & more attractive fit for the fuel cap itself. We have also whilst keeping them flat designed in a smooth & slight dome to enable a little more fuel capacity.

We are able to offer these as outright purchases if you want to keep your standard tank or as an exchange service and you can choose from a choice of polished, satin black, repsol gp orange (which the factory wheels are done in) or pale repsol orange which is the match to the standard repsol frame stickers. PLEASE STATE YOUR COLOUR WHEN ORDERING

£395 exchange or £525 outright

IF YOU ORDER ONLINE & OPT FOR THE EXCHANGE SERVICE,WE WILL SEND OUT YOUR TANK WHEN WE RECEIVE YOURS.

The only billet gas caps in the world for the fantastic Montesa 4RT are now avaliable direct from H&D Racing. These have been in development for 3 years and we have finally got everything right for a product that needs to be as excellent a quality and good looks as the machine that it is designed to fit and we are very proud to be the 1st to have these out for Montesa owners to fit to their machines.

Machined out of aerospace spec billet alluminium and then anodised in either gold/red or black and then laser etched & machined to give the awesome finished product that you see here, we have made these with a special breather to enable to fitting of our excellent billet vent caps as well as the standard rubber. These are supplied with the genuine seals kits also, simply open the pack, remove the old plastic top and fit, bingo. To make the best look for your new cap we always reccomend one our billet breathers!

I different picture of all 3 colours is on the new products page